CWNA-107 CWNP Certified Wireless Network Administrator exact Exam Questions

Certified Wireless Network Administrator

Last Update 21 hours ago Total Questions : 156

The Certified Wireless Network Administrator content is now fully updated, with all current exam questions added 21 hours ago. Deciding to include CWNA-107 practice exam questions in your study plan goes far beyond basic test preparation.

You'll find that our CWNA-107 exam questions frequently feature detailed scenarios and practical problem-solving exercises that directly mirror industry challenges. Engaging with these CWNA-107 sample sets allows you to effectively manage your time and pace yourself, giving you the ability to finish any Certified Wireless Network Administrator practice test comfortably within the allotted time.

Question # 1

In a WALN security, what authentication method always creates Layer2 dynamic encryption keys?

Shared Key

WEP

HTTPS captive portal

EAP-TLS

Question # 2

You are troubleshooting a problem with interference from a non-802.11 device. Given that the device is not a WLAN device, you cannot use a protocol analyzer and have chosen to use a spectrum analyzer. You want to view the signal from the interfering device over time to see the activity that is generating.

What common spectrum analyzer view should you use for this analysis?

Waterfall/Spectrogram

Real-time FFT

APs

Clients

Question # 3

What statement about 802.3, Clause 33 Power over Ethernet is true?

Only midspan PSEs are supported.

The lowest voltage drop is achieved when using CAT6 instead of Cat5 or CAT5e.

Only endpoint PSEs are supported.

When using CAT5 cabling, you increase the maximum draw available to the PD over that available with CAT6.

Question # 4

You are troubleshooting a controller-based AP that is unable to locate the controller. DHCP is not use and the controller is located at 10.10.10.81/24 while the AP is on the 10.10.16.0/24 network. What should be inspected to verify proper configuration?

NTP

BOOTH

DNS

AP hosts file

Question # 5

A standard PoE injector is used to power an access point requiring 802.3at. CAT6 cabling is in use. What is the maximum distance supported between the access point and the Ethernet switch with the use of a midspan power injector?

100 meters

300 meters

328 meters

200 meters

Question # 6

When using a spectrum analyzer to look for non-Wi-Fi interference sources, you notice significant interference across the entire 2.4 GHz band (not on a few select frequencies) within the desktop area of a user’s workspace, but the interference disappears quickly after just 2 meters. What is the most likely cause of this interference?

USB 3 device in the user’s work area

Bluetooth devices in the user’s work area

Excess RF energy from a nearby AP

Unintentional radiation from the PC power supply

Question # 7

You are planning for PoE in a standard office deployment. Which one of these devices is least likely to be a PoE PD?

Video camera

Access point

VoIP phone

Ethernet switch

Question # 8

When performing a validation survey for a Multiple Channel Architecture (MCA) system in a multi-tenant building with five floors, what aspect should you, as the surveyor, keep in mind?

The RF interference caused by passing airplanes supporting on-board Wi-Fi should be a prime consideration

The channel reuse pattern should be three dimensional with the RF cell extending coverage of each access point to other floors

The omni-directional antennas of the access points should be oriented parallel to the floor to maximize the coverage pattern across as many floors as possible

The Fresnel Zone is completely blocked between floors so each floor is considered a separate site survey

Question # 9

You are deploying a WLAN monitoring solution that utilizes distributed sensor devices. Where should sensors be deployed for best results?

Every 20 feet and alongside each AP

Closer to the APs

Closer to the client devices

In critical areas where WLAN performance must be high

Question # 10

You are reporting on the RF environment in your facility. The manager asks you do describe the noise floor noted on the report. Which of the following is the best explanation?

The energy radiated by flooring materials that causes interference in the 2.4 GHz and 5 GHz bands.

The noise caused by elevators, microwave ovens, and video transmitters.

The RF energy that exists in the environment from intentional and unintentional RF radiators that forms the baseline above which the Intentional signal of your WLAN must exist.

The extra energy radiated by access points and client devices beyond that intended for the signal.