Summer Goodies - 55% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: av5rz84q

Exact2Pass Menu

Login / Register

Question # 4

Exhibit.

Referring to the exhibit, there are multiple ASM groups in the 224 0 0.0/4 range

Which configuration change is needed to ensure R1 is always the RP for group 224.224.1.1?

A.

Increase the priority on R1 to higher than R2

B.

Configure R1 with a higher local RP address

C.

Set the priority on R1 to zero

D.

Ensure R1 has a more specific group range

Full Access
Question # 5

What are three well-known mandatory BGP attributes? (Choose three.)

A.

AS-path

B.

community

C.

origin

D.

MED

E.

next-hop

Full Access
Question # 6

Exhibit.

Referring to the exhibit, which two statements are true with regards to deploying CoS? (Choose two.)

A.

You should apply BA classifiers on the point-to point interfaces of the routers.

B.

You should apply MF classifiers on the LAN-facing interfaces of the routers

C.

You should apply BA classifiers on the LAN-facing interfaces of the routers

D.

You should apply MF classifiers on the point-to-point interfaces of the routers

Full Access
Question # 7

Click the Exhibit button.

You have configured and applied the policer shown in the exhibit to your Junos device.

Which statement is true in this scenario?

A.

Traffic exceeding the committed-burst size will be marked with a loss priority of high.

B.

Traffic exceeding the excess-burst size will be discarded.

C.

Traffic exceeding the committed-information-rate will be rate limited.

D.

Traffic exceeding the committed-burst size will be discarded.

Full Access
Question # 8

Exhibit.

You are configuring, the PVLAN feature on your switches. The PVLAN will span the two EX Series switches shown in the exhibit

Which three configuration parameters must be enabled on the ports connecting the two switches? (Choose three. )

A.

family inet

B.

interface-mode access

C.

interface-mode trunk

D.

family Ethernet-switching

E.

inter-switch-link

Full Access
Question # 9

Exhibit.

A router is attempting to form an OSPF neighborship with another router However, the OSPF neighborship fails to establish completely Referring to the exhibit, what is the problem?

A.

There is an OSPF area mismatch

B.

There is an interface MTU mismatch

C.

There is an interface subnet mask mismatch

D.

There is an interface type mismatch

Full Access
Question # 10

Click the Exhibit button.

Referring to the exhibit, how is R1 learning the route from R2?

R2 has an export policy with external type 2 configured.

A.

R2 has interface ge-0/0 configured as a passive interface under OSPFv3.

B.

R2 has interface ge-0/0/2 configured as a passive interface under OSPFv3.

C.

R2 has an interface policy with external type 1 configured.

D.

R2 has interface ge-0/0/2 configured in another area under OSPFv3.

Full Access
Question # 11

When redistributing IGP routes into BGP. what information .s used by default on Junos platforms to determine the BGP route's MED attribute value?

A.

routing information base

B.

the IGP route preference

C.

the IGP Metric

D.

route protocol source

Full Access
Question # 12

Your network has Junos Fusion configured with MX960 routers as aggregation devices (AD) and QFX5100 switches as satellite devices (SO) Which two statements are coned in this scenario? (Choose two )

A.

The AD runs the Junos software for all its connected SDs.

B.

The Fusion extended ports are configured on the SDs.

C.

SDs are added to the AD by configuring the cascade port on the AD.

D.

All SDs connected to a single AD must use the same software version.

Full Access
Question # 13

You will to route Layer 3 PVLAN traffic within the secondary VLAN.

What is required to accomplish this task?

A.

a community VIAN

B.

an IRB

C.

an FBF policy

D.

an isolated VLAN

Full Access