One of the information that is communicated by bits in the PHY header is data rate. Data rate is the speed at which data is transmitted or received over the wireless medium. Data rate depends on factors such as modulation, coding, channel width, spatial streams, and guard interval. Data rate is indicated by bits in different fields of the PHY header, depending on the type of PPDU (e.g., OFDM, HT, VHT, HE). The receiver uses these bits to determine how to decode and demodulate the rest of the PPDU. The other options are not correct, as they are not communicated by bits in the PHY header. SNR (Signal-to-Noise Ratio), noise, and signal strengthare measured by the receiver based on its own capabilities and environment. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 101-105

The HT protection mode in which an AP is operating can be identified by looking at the HT Operations element in a Beacon frame. The HT Operations element is a part of the Beacon frame that contains information about the High Throughput (HT) capabilities and operation of an 802.11n BSS. The HT Operations element has a field called HT Protection, which indicates how the BSS protects its HT transmissions from interference or collisions with non-HT devices or BSSs. The HT Protection field can have four values: No Protection, Nonmember Protection, 20 MHz Protection, or Non-HT Mixed Mode. The other options are not correct, as they do not contain information about the HT protection mode. The HT Protection element does not exist, the ERP Information element is used for Extended Rate PHY (ERP) protection mode for 802.11g devices, and the HT Capabilities element is used for indicating the supported HT features of an individual device. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 125-126

The Group Key Handshake consists of two frames excluding any Ack frames that may be required. The Group Key Handshake is used to distribute and update the Group Temporal Key (GTK) for encrypting broadcast and multicast traffic. The AP initiates the Group Key Handshake by sending a Group Key Message 1 frame to a STA, which contains the new GTK and other information. The STA responds with a Group Key Message 2 frame to the AP, which confirms the receipt of the GTK and other information. After this, both the AP and the STA can use the new GTK for encryption and decryption of broadcast and multicast traffic . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 7: 802.11 Security, page 246; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 7: 802.11 Security, page 247.

Receive sensitivity is the minimum signal level that a receiver can detect and decode. Different devices may have different receive sensitivity levels depending on their hardware specifications and antenna configurations. In this scenario, the portable analyzer has a lower receive sensitivity than the AP, meaning that it requires a stronger signal to capture the packets from the client STA. The AP, on the other hand, has a higher receive sensitivity and can receive the packets from the client STA even if they have a weaker signal. This explains why the portable analyzer can only see unidirectional traffic from the AP to the client when capturing near the AP5 References:

• CWAP-403 Study Guide, Chapter 4: PHY Layer Analysis, page 121
• CWAP-403 Objectives, Section 4.3: Analyze PHY layer metrics

The function of the PHY preamble is to allow the receiver to detect and synchronize with the signal. The PHY preamble is a part of the PPDU that is transmitted before the PHY header and the PSDU. The PHY preamble consists of a series of training fields that help the receiver to adjust its parameters, such as frequency, timing, and gain, to match the incoming signal. The PHY preamble also helps the receiver to estimate the channel conditions and noise level. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 99-100

Observing the problem is the most important step in the WLAN troubleshooting methodology among those listed. This step involves capturing and analyzing the relevant data from the wireless network, such as packets, frames, spectrum, and performance metrics. Observing the problem helps to verify the existence and scope of the issue, identify the root cause and possible solutions, and validate the results of any actions taken. The other steps are also important, but they are not as critical as observing the problem12 References:

• CWAP-404 Study Guide, Chapter 1: Troubleshooting Methodology, page 15
• CWAP-404 Objectives, Section 1.2: Observe the problem

The value of the Listen Interval field in an Association Request frame indicates how often a STA in power save mode wakes up to listen to Beacon frames. The Listen Interval is expressed in units of Beacon Intervals (typically 100 TU or 102.4 ms). For example, if the Listen Interval is set to 10, it means that the STA will wake up every 10 Beacon Intervals (or about 1 second) to check for buffered frames at the AP. The Listen Interval is used by the AP to determine how long it can hold frames for a STA in power save mode before discarding them . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 197; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 198.