H35-260 Huawei HCSA-Field-Transmission & PTN V1.0 exact Exam Questions

HCSA-Field-Transmission & PTN V1.0

Last Update 4 hours ago Total Questions : 326

The HCSA-Field-Transmission & PTN V1.0 content is now fully updated, with all current exam questions added 4 hours ago. Deciding to include H35-260 practice exam questions in your study plan goes far beyond basic test preparation.

You'll find that our H35-260 exam questions frequently feature detailed scenarios and practical problem-solving exercises that directly mirror industry challenges. Engaging with these H35-260 sample sets allows you to effectively manage your time and pace yourself, giving you the ability to finish any HCSA-Field-Transmission & PTN V1.0 practice test comfortably within the allotted time.

Question # 11

When the data link layer of a router (IP forwarding) receives a packet whose length is greater than the maximum MTU of the interface that the router will send out, which of the following strategies is adopted?

Drop the group

Fragment the packet

Make a request to the router to reduce its packet size

Forward the packet directly

Question # 12

Which of the following factors is related to pointer adjustment?

The clocks of each NE are not synchronized

Rate

Expenses

Scrambling

Question # 13

When using OptiX Datacollector to collect data, it can be collected by network element, which means to collect the fault data of all boards below the network element, or it can be collected by single board to collect

the fault data of a single board under the network element.

True

False

Question # 14

Which one is wrong in the description of hardware redundancy backup of PTN7900-32?

SCA board 1+1 backup

XCS board 6+1 backup

3+3/4+4/5+5 backup of power supply

Fan 1+1 Backup

Question # 15

Any service cross-connect can only be configured in inter-board cross-connect, and does not require the participation of XCS boards

True

False

Question # 16

Which of the following descriptions about electrical layer service configuration is wrong?

When the OCh service path exists, create the Client path directly, and the NMS can automatically create the OTUk and ODUk paths

When there is an OCh service path, you can first search for the OTUK path, create the ODUk service layer path, and then create the Client path

When the OCh service path exists, directly create the ODUk path, and the network management can automatically create the OTUk path

After the logical fiber connection is completed, no path search operation is required, and the OTS path and OMS path can automatically

generate the

Question # 17

Where in the L2/L3 node is the VLAN in the Layer 2 header stripped in the packet sent by the base station in the LTE solution?

L3VE sub-interface

Network side interface

LOOPBACK interface

Question # 18

Which of the following technologies is used in the dynamic BGP MPLS L3VPN to distinguish the same IP address in different VPNs in the BGP protocol?

VRF

Export RT

Import RT

Question # 19

When enabling NE performance monitoring events on the U2000 network management system, which of the following options are correct?

Set the monitoring start time of 15 minutes on the U2000 (must be later than the current time of the NMS and NEs)

Set the monitoring start time of 15 minutes on the U2000 (it can be earlier than the current time of the NMS and NEs)

15-minute monitoring end time (must be later than 15-minute monitoring start time), can not be set

15 minutes monitoring end time (must be later than 15 minutes monitoring start time), must be set

Question # 20

What are the possible reasons for the failure of route calculation by the optical layer path (OCh level)?

The optical fiber is connected incorrectly. The wavelength of the WDM side port of the OTU board is inconsistent with the wavelength of the optical crossover.

Network layer OTS path is missing

The fiber attenuation between the TDC and RDC ports of the OAU board is too

large