To create a LAG interface, you need to perform two actions: enable LAG on the chassis and on each member interface. The first action is to configure the chassis stanza with the aggregated-devices statement and specify the number of LAG interfaces and the link-speed for each interface. The second action is to configure each member interface with the family ethernet-switching statement and the aggregated-ether-options statement with the lacp option. The name of the first LAG interface is not relevant, as long as it matches the name of the aggregated interface under the interfaces stanza. The name can be ae0, ae1, or any other valid name. References:

Enterprise Routing and Switching, Specialist (JNCIS-ENT) - Juniper Networks

Enterprise Routing and Switching, Specialist (JNCIS-ENT) - Juniper Networks

[Junos OS Layer 2 Configuration Guide - TechLibrary - Juniper Networks]

[Junos OS Layer 2 Configuration Guide - TechLibrary - Juniper Networks]

Junos devices support various types of tunnels for different purposes 1 2 .

Option B is correct.  Generic Routing Encapsulation (GRE) is a tunneling protocol that can encapsulate a wide variety of network layer protocols inside virtual point-to-point links over an Internet Protocol network 1 .  Junos devices support GRE tunnels 1 .

Option D is correct.  IPsec (Internet Protocol Security) is a protocol suite for securing Internet Protocol (IP) communications by authenticating and encrypting each IP packet of a communication session 1 .  Junos devices support IPsec tunnels 1 .

Option A is incorrect. Spanning Tree Protocol (STP) is not a type of tunnel.  It’s a network protocol designed to prevent loops in a bridged Ethernet local area network 2 .

Option C is incorrect.  While Junos devices do support IP-IP (also known as IP tunneling), it’s not supported on all Junos devices 1 .

A  is correct because you can deploy only stateless firewall filters on an EX Series switch.  A stateless firewall filter is a filter that evaluates each packet individually based on the header information, such as source and destination addresses, protocol, and port numbers 1 .  A stateless firewall filter does not keep track of the state or context of a packet flow, such as the sequence number, flags, or session information 1 .  EX Series switches support only stateless firewall filters, which are also called access control lists (ACLs) or packet filters 2 .

C  is correct because you can apply firewall filters to both Layer 2 and Layer 3 traffic on an EX Series switch.  Layer 2 traffic is traffic that is switched within a VLAN or a bridge domain, while Layer 3 traffic is traffic that is routed between VLANs or networks 3 .  EX Series switches support three types of firewall filters: port (Layer 2) firewall filters, VLAN firewall filters, and router (Layer 3) firewall filters 4 . You can apply these filters to different interfaces and directions to control the traffic entering or exiting the switch.

IS-IS (Intermediate System to Intermediate System) is a routing protocol that is designed to move information efficiently within a computer network 1 2 .  It supports multiple protocol topologies, including IPv4, IPv6, and multicast 1 2 . Therefore, options C, E, and D are correct.

B  is correct because the loops do not exist is one of the conditions that are verified by the receiving router to ensure that the received BGP route is valid.  A loop in BGP means that a route has been advertised by the same AS more than once, which can cause routing instability and inefficiency 1 .  To prevent loops, BGP uses the AS-path attribute, which lists the AS numbers that a route has traversed from the origin to the destination 2 .  The receiving router checks the AS-path attribute of the received route and discards it if it finds its own AS number in the list 2 . This way, BGP avoids accepting routes that contain loops.

C  is correct because the next hop is reachable is one of the conditions that are verified by the receiving router to ensure that the received BGP route is valid.  The next hop is the IP address of the next router that is used to forward packets to the destination network 3 .  The receiving router checks the next hop attribute of the received route and verifies that it has a valid route to reach it 3 .  If the next hop is not reachable, the received route is not usable and is rejected by the receiving router 3 . This way, BGP ensures that only feasible routes are accepted.

https://www.juniper.net/documentation/us/en/software/junos/cli-reference/topics/ref/statement/lsa-refresh-interval-edit-protocols-ospf.html

The configuration shown in the exhibit is an example of a routing instance of type virtual-router.  A routing instance is a collection of routing tables, interfaces, and routing protocol parameters that create a separate routing domain on a Juniper device 1 .  A virtual-router routing instance allows administrators to divide a device into multiple independent virtual routers, each with its own routing table 2 .

The configuration also includes a rib-group statement, which is used to import routes from one routing table to another. A rib-group consists of an import-rib statement, which specifies the source routing table, and an export-rib statement, which specifies the destination routing table.

In this case, the rib-group name is inet-to-ispi, and the import-rib statement specifies inet.0 as the source routing table. The export-rib statement specifies ispi.inet.0 as the destination routing table. This means that the routes from inet.0 will be imported into ispi.inet.0.

Therefore, the correct answer is B. The inet.0 route table will be imported into the ispi.inet.0 route table.