201-450 LPIC-2 Exam 201, Part 1 of 2, version 4.5 exact Exam Questions

LPIC-2 Exam 201, Part 1 of 2, version 4.5

Last Update 15 hours ago Total Questions : 161

The LPIC-2 Exam 201, Part 1 of 2, version 4.5 content is now fully updated, with all current exam questions added 15 hours ago. Deciding to include 201-450 practice exam questions in your study plan goes far beyond basic test preparation.

You'll find that our 201-450 exam questions frequently feature detailed scenarios and practical problem-solving exercises that directly mirror industry challenges. Engaging with these 201-450 sample sets allows you to effectively manage your time and pace yourself, giving you the ability to finish any LPIC-2 Exam 201, Part 1 of 2, version 4.5 practice test comfortably within the allotted time.

Question # 31

Which of the following filter keywords for tcpdump specify the transfer direction for network packets? (Choose TWO correct answers.)

source

src

dest

src or dst

both

Question # 32

Under which of the following circumstances would the command ping output the string (DUP!)?

When the ICMP packets are send to a broadcast address and multiple hosts respond.

When the host being sent ICMP packets is on a different network.

When the router responds to the ICMP packet in addition to the host receiving the ICMP packets.

When the host sending the ICMP packet is the same host as the one receiving the ICMP packets.

Question # 33

Considering the following kernel IP routing table below, which of the following commands must be used to remove the route to the network 10.10.1.0/24? (Select TWO answers)

Kernel IP routing table

Destination Gateway Genmask Flags Metric Ref Use Iface

203.0.113.162 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0

172.16.87.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0

192.168.246.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1

10.10.1.0 192.168.246.11 255.255.255.0 UG 0 0 0 eth1

127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo

0.0.0.0 203.0.113.162 0.0.0.0 UG 0 0 0 ppp0

ip net delete 10.10.1.0/24

route del 10.10.1.0/24

route del -net 10.10.1.0/24

route del 10.10.1.0/24 gw 192.168.246.11

ip route delete 10.10.1.0/24

Question # 34

What is incorrect about these entries in /etc/hosts which could be causing host name lookup problems with host2?

host1 192.168.1.12

host2 192.168.1.12

Two host names are using the same IP address.

The server doing the query is on a different subnet.

The fields are out of order.

host2 is not a fully qualified domain name.

Question # 35

What should be done to ensure a client machine uses the recursive nameserver running on the IP address 192.168.0.1? (Choose TWO correct answers.)

Add nameserver 192.168.0.1 to /etc/resolv.conf.

Run route add nameserver 192.168.0.1.

Run ifconfig eth0 nameserver 192.168.0.1.

Ensure that the dns service is listed in the hosts entry in the /etc/nsswitch.conf file.

Run bind add nameserver 192.168.0.1.

Question # 36

Please enter the complete path to the main SysV init process configuration file.

Question # 37

After changing the default runlevel in the SysV-init configuration file, the system boots in a different than intended runlevel. Where else could this different runlevel be defined?

In the /etc/sysctl.conf

In the boot loader configuration file

In the /etc/runlevel file

In the /boot/initramfs file

In the /etc/rc.d/rc.local file

Question # 38

In case the file containing the Linux kernel is lost, what happens when the system is booting?

The system starts normally since the bootloader copies the kernel to the master boot record of the hard disk.

Instead of the kernel, the initramfs is loaded and instructed to mount the root filesystem and reinstall the kernel from the original package or from source.

The bootloader mounts the root filesystem read-only and launches /bin/sh directly in order to allow the administrator to reinstall the kernel.

Without a kernel a system cannot boot and, depending on the bootloader, an error is displayed.

Question # 39

A Linux server is running in single user mode for regular maintenance. Which commands are used to restore the server to its usual runlevel? (Choose TWO correct answers.)

telinit 0

shutdown -r now

sync

shutdown -h now

reboot

Question # 40

Which command is used to install a new LILO boot loader?

lilo

lilo-config

lilo-install

install-lilo