NS0-184 Netapp NetApp Certified Storage Installation Engineer

NetApp Certified Storage Installation Engineer - ONTAP

Last Update 10 hours ago Total Questions : 60

The NetApp Certified Storage Installation Engineer - ONTAP content is now fully updated, with all current exam questions added 10 hours ago. Deciding to include NS0-184 practice exam questions in your study plan goes far beyond basic test preparation.

You'll find that our NS0-184 exam questions frequently feature detailed scenarios and practical problem-solving exercises that directly mirror industry challenges. Engaging with these NS0-184 sample sets allows you to effectively manage your time and pace yourself, giving you the ability to finish any NetApp Certified Storage Installation Engineer - ONTAP practice test comfortably within the allotted time.

Question # 11

You have completed a base installation and system registration of an AFF A250 system, but you notice that you have one failed drive. Neither “un-failing” nor reseating the drive helped to repair it. You must ensure proper replacement of the failed drive.

In this scenario, which two actions should you take? (Choose two.)

Ask the customer to open a technical case with NetApp Support.

Ask the customer for a drive with the same capacity and replace it.

Run Active IQ Config Advisor to collect all the logs on the system.

Power off the system until the drive has been replaced.

Question # 12

You have a 2-node FAS8300 ONTAP 9.8 cluster that serves SMB shares. You are configuring interface groups for higher performance and resiliency.

Which two NetApp best practices should you follow to satisfy these performance and resiliency requirements? (Choose two.)

Use ports from different NICs.

Use ports from the same NICs.

Use ports with different chipsets.

Use ports with the same chipsets.

Question # 13

After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works.

In this scenario, which two commands would you use to accomplish this task? (Choose two.)

system node autosupport history show

system node autosupport check show

system node autosupport destination show

system node autosupport invoke

Question # 14

You want to disconnect a DS224C shelf with 3.8 TB NetApp Storage Encryption (NSE) SSDs to an AFF A300 HA pair with two DS224C shelves with 3.8 TB SSDs without NSE in one stack.

In this scenario, how would you add the shelf?

Add the shelf to the existing stack.

Create a new stack on the HA pair to add the shelf.

Connect the shelf to an HA pair with NSE drives.

License NSE and add the shelf to this HA pair as a new stack.

Question # 15

You are installing an AFF A700 system with two disk shelves using ADPv2. After setting up the cluster, you realize that one drive shelf was powered off and that the drives have not been assigned to any of the nodes.

In this scenario, which two resources will help you find a solution? (Choose two.)

Active IQ Config Advisor

NetApp Documentation Center

NetApp Knowledge Base

Active IQ Digital Advisor

Question # 16

Your customer wants to know more about the network configuration within the cluster.

In this scenario, which statement is correct about a LIF?

A LIF is a port that provides physical connections.

A LIF is created within a broadcast domain and contains a pool of IP address.

A LIF is an IP address or a WWPN that is associated with a port.

A LIF separates network domains to access cluster data.

Question # 17

You installed a new 2-node FAS500f ONTAP 9.8 switchless cluster that serves NAS volumes to both NFSv4.1 and SMB clients. The host operating systems have full flow control enabled on their data ports.

In this scenario, which two flow control settings would you verify? (Choose two.)

Verify that the data network ports have full flow control disabled.

Verify that the cluster network ports have full flow control enabled.

Verify that the data network ports have full flow control enabled.

Verify that the cluster network ports have full flow control disabled.

Question # 18

You have added two new AFF A250 nodes to an existing 4-node cluster with NetApp CN1610 cluster network switches. Although the nodes can join the cluster, the storage failover show command output shows that the NVRAM log is not synchronized, and it cannot reach the partner over an HA interconnect.

In this scenario, which two statements are true? (Choose two.)

The AFF A250 requires switches with 40GbE port support.

The AFF A250 uses different ports for the cluster and the HA interconnect.

The AFF A250 requires switches with 25GbE port support.

The AFF A250 uses the same port for the cluster and the HA interconnect.