Summer Sale Special 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: ex2p65

Exact2Pass Menu

Aruba Certified Campus Access Professional Exam

Last Update 19 hours ago Total Questions : 119

The Aruba Certified Campus Access Professional Exam content is now fully updated, with all current exam questions added 19 hours ago. Deciding to include HPE7-A01 practice exam questions in your study plan goes far beyond basic test preparation.

You'll find that our HPE7-A01 exam questions frequently feature detailed scenarios and practical problem-solving exercises that directly mirror industry challenges. Engaging with these HPE7-A01 sample sets allows you to effectively manage your time and pace yourself, giving you the ability to finish any Aruba Certified Campus Access Professional Exam practice test comfortably within the allotted time.

Question # 4

What are the requirements to ensure that WMM is working effectively'? (Select two)

A.

The APs and the controller are Wi-Fi CERTIFIED for WMM which is enabled

B.

All APs need to be from the AP-5xx series and AP-6xx series which are Wi-Fi CERTIFIED 6.

C.

The Client must be Wi-Fi CERTIFIED for WMM and configured for WMM marking.

D.

The Aruba AOS10 APs installed have to be converted to controlled mode

E.

The AP needs to be connected via a tagged VLAN to the wired port

Question # 5

Your Aruba CX 6300 VSF stack has OSPF adjacency over SVI 10 with LAG 1 to a neighboring device The following configuration was created on the switch:

A)

B)

C)

D)

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Question # 6

You need to drop excessive broadcast traffic on an ingress port or an ArubaOS-CX switch. What is the best feature to use for this task?

A.

DWRR queuing

B.

Strict queuing

C.

Rate limiting

D.

QoS shaping

Question # 7

Refer to the exhibit.

A company has deployed 200 AP-635 access points. To but is not working as expected

What would be the correct action to fix the issue?

A.

Change the SSID to WPA3-Enhanced Open

B.

Change the SSID to WPA3-Enterprise (CCM).

C.

Change the SSID to WPA3-Personal

D.

Change the SSID to WPA3-Enterpnse (CNSA).

Question # 8

You are are doing tests in your lab and with the following equipment specifications:

• AP1 has a radio that generates a 16 dBm signal.

• AP2 has a radio that generates a 13 dBm signal.

• AP1 has an antenna with a gain of 8 dBi.

• AP2 has an antenna with a gain of 12 dBi. The antenna cable for AP1 has a 4 dB loss. The antenna cable for AP2 has a 3 dB loss.

What would be the calculated Equivalent Isotropic Radiated Power (EIRP) for AP1?

A.

-9 dBm

B.

20 dBm

C.

40 dBm

D.

15 dBm

Question # 9

A customer wants to provide wired security as close to the source as possible The wired security must meet the following requirements:

-allow ping from the IT management VLAN to the user VLAN

-deny ping sourcing from the user VLAN to the IT management VLAN

The customer is using Aruba CX 6300s

What is the correct way to implement these requirements?

A.

Apply an outbound ACL on the user VLAN allowing temp echo-reply traffic toward the IT management VLAN

B.

Apply an inbound ACL on the user VLAN allowing icmp echo-reply traffic toward the IT management VLAN

C.

Apply an inbound ACL on the user VLAN denying icmp echo traffic toward the IT management VLAN

D.

Apply an outbound ACL on the user VLAN denying icmp echo traffic toward the IT management VLAN

Question # 10

A customer just upgraded aggregation layer switches and noticed traffic dropping for 120 seconds after the aggregation layer came online again. What is the best way to avoid having this traffic dropped given the topology below?

A.

Configure the linkup delay timer to 240 seconds to double the amount of lime for the initial phase to sync

B.

Configure the linkup delay timer to exclude LAGS 101 and 102, which will allow time for routing adjacencies to form and to learn upstream routes

C.

Configure the linkup delay timer to include LAGs 101 and 102, which will allow time for routing adjacencies lo form and to learn upstream routes

D.

Configure the linkup delay timer to 120 seconds, which will allow the right amount of time for the initial phase to sync

Go to page: