300-410 Cisco Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI) exact Exam Questions

Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI)

Last Update 5 hours ago Total Questions : 642

The Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI) content is now fully updated, with all current exam questions added 5 hours ago. Deciding to include 300-410 practice exam questions in your study plan goes far beyond basic test preparation.

You'll find that our 300-410 exam questions frequently feature detailed scenarios and practical problem-solving exercises that directly mirror industry challenges. Engaging with these 300-410 sample sets allows you to effectively manage your time and pace yourself, giving you the ability to finish any Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI) practice test comfortably within the allotted time.

Question # 181

Refer to the exhibit.

An engineer configures DMVPN and receives the hub location prefix of 10.1.1.0724 on R2 and R3 The R3 prefix of 10 1.3.0/24 is not received on R2. and the R2 prefix 10.1,2.0/24 is not received on R3. Which action reserves the issue?

Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the command no ip split-horizon eigrp 10 on the tunnel interface of R1

There is no spoke-to-spoke connection DMVPN configuration should be modified to enable a tunnel connection between R2 and R3 and neighbor relationship confirmed by use of the show ip eigrp neighbor command

Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the no ip split-horizon eigrp 10 command on the Gi0/0 interface of R1.

There is no spoke-to-spoke connection DMVPN configuration should be modified with a manual neighbor relationship configured between R2 and R3 and confirmed bb use of the show ip eigrp neighbor command.

Question # 182

Refer to the exhibit. A network engineer receives a report that Spoke 1 users can perform bank transactions with the server located at the Center site, but Spoke 2 users cannot. Which action resolves the issue?

Configure the Spoke 2 users IP on the router B OSPF domain

Configure encapsulation dot1q 78 on the router C interface.

Configure IPv6 on the routers B and C interfaces

Configure OSPFv2 on the routers B and C interfaces

Question # 183

Exhibit.

Refer to the exhibit. A network is configured for EIGRP equal-cost load balancing, but the traffic destined to the servers is not load balanced. Link metrics from router R2 to R3 and R4 are the same. Which delay value must be configured to resolve the issue?

208 oon R3 E0/0

120 on R4 E0/1

120/on R3 E0/1

2200 on R4 E0/1

Question # 184

An engineer configured VRF-Lite on a router for VRF blue and VRF red. OSPF must be enabled on each VRF to peer to a directly connected router in each VRF. Which configuration forms OSPF neighbors over the network 10.10.10.0/28 for VRF blue and 192.168.0.0/30 for VRF red?

Option A

Option B

Option C

Option D

Question # 185

Refer to the exhibit. An engineer configured NetFlow on R1, but the flows do not reach the NMS server from R1. Which configuration resolves this Issue?

Option A

Option B

Option C

Option D

Question # 186

Refer to the exhibit.

The network administrator configured the network to establish connectivity between all devices and notices that the ASBRs do not have routes for each other. Which set of configurations resolves this issue?

Option A

Option B

Option C

Option D

Question # 187

Refer to the exhibit. An engineer is troubleshooting a prefix advertisement issue from R3, which is not directly connected to R1. Which configuration resolves the issue?

Option A

Option B

Option C

Option D

Question # 188

:583

Refer to the exhibit. R1 is directly connected to R2 over network 10.100.14.0/24. An engineer configures R1 to advertise a static route that is connected to a local loopback for network 10.100.13.0/24. The network is not in the routing table of R2. Which action resolves the issue?

The redistribution command isincorrect on R1 The default metric metric 200 should be inducted with the redistribution command.

The Loopback interface on R1 is administratively down The interface should be enabled with the no shutdown command

R2 must use a different OSPF process number and should be changed lo ospf 1 to match R1

The redistribution command is incorrect on R1 The keyword subnets should be included with the redistribution command