300-410 Cisco Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI) exact Exam Questions

Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI)

Last Update 5 hours ago Total Questions : 642

The Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI) content is now fully updated, with all current exam questions added 5 hours ago. Deciding to include 300-410 practice exam questions in your study plan goes far beyond basic test preparation.

You'll find that our 300-410 exam questions frequently feature detailed scenarios and practical problem-solving exercises that directly mirror industry challenges. Engaging with these 300-410 sample sets allows you to effectively manage your time and pace yourself, giving you the ability to finish any Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI) practice test comfortably within the allotted time.

Question # 61

Refer to the exhibit.

An engineer has configured DMVPN on a spoke router. What is the WAN IP address of another spoke router within the DMVPN network?

172.18.46.2

192.168.1.4

172.18.16.2

192.168.1.1

Question # 62

Refer to the exhibit.

The ACL is placed on the inbound Gigabit 0/1 interface of the router. Host

192.168.10.10cannot SSH to host 192.168.100.10 even though the flow is permitted. Which action

resolves the issue without opening full access to this router?

Move the SSH entry to the beginning of the ACL

Temporarily move the permit ip any any line to the beginning of the ACL to see if the flow works

Temporarily remove the ACL from the interface to see if the flow works

Run the show access-list FILTER command to view if the SSH entry has any hit statistic associated with it

Question # 63

Refer the exhibit.

Which action resolves intermittent connectivity observed with the SNMP trap

packets?

Decrease the committed burst Size of the mgmt class map

Increase the CIR of the mgmt class map

Add a new class map to match TCP traffic

Add one new entry in the ACL 120 to permit the UDP port 161

Question # 64

An engineer is troubleshooting on the console session of a router and turns on multiple debug commands. The console screen is filled with scrolling debug messages that none of the commands can be verified if entered correctly or display any output. Which action allows the engineer to see entered console commands while still continuing the analysis of the debug messages?

Configure the logging synchronous command

Configure the no logging console debugging command globally

Configure the logging synchronous level all command

Configure the term no mon command globally

Question # 65

What are two functions of IPv6 Source Guard? (Choose two.)

It uses the populated binding table for allowing legitimate traffic.

It works independent from IPv6 neighbor discovery.

It denies traffic from unknown sources or unallocated addresses.

It denies traffic by inspecting neighbor discovery packets for specific pattern.

It blocks certain traffic by inspecting DHCP packets for specific sources.

Question # 66

Refer to the exhibit.

A network engineer is adding a new spoke router into an existing DMVPN Phase 3 tunnel with a hub router to provide secure communication between sites Which additional configuration must the engineer apply to enable the tunnel to come up?

ip nhrp registration no-unique

ip nhrp server-only non-caching

ip nhrp responder tunnel

ip nhrpnhs 172.23.5.1

Question # 67

Which Layer 3 VPN attribute installs customer routes in the VRF?

extended-community

MPLS label

Question # 68

Refer to the exhibit.

An engineer configured NetFlow on R1, but the NMS server cannot see the flow from ethernet 0/0 of R1. Which configuration resolves the issue?

flow monitor Flowmonitor1source Ethernet0/0

interface Ethernet0/1ip flow monitor Flowmonitor1 inputip flow monitor Flowmonitor1 output

interface Ethernet0/0ip flow monitor Flowmonitor1 inputip flow monitor Flowmonitor1 output

flow exporter FlowAnalyzer1source Ethernet0/0

Question # 69

Refer to the exhibit. A network administrator configured mutual redistribution on R1 and R2 routers, which caused instability in the network. Which action resolves the issue?

Set a tag in the route map when redistributing EIGRP into OSPF on R1. and match the same tag on R2 to deny when redistributing OSPF into EIGRP.

Set a tag in the route map when redistributing EIGRP into OSPF on R1. and match the same tag on R2 to allow when redistributing OSPF into EIGRP.

Advertise summary routes of EIGRP to OSPF and deny specific EIGRP routes when redistributing into OSPF.

Apply a prefix list of EIGRP network routes in OSPF domain on R1 to propagate back into the EIGRP routing domain.

Question # 70

Refer to the exhibit.

An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+. Which action produces the desired configuration?

Add the aaa authentication login default none command to the global configuration.

Replace the capital “C” with a lowercase “c” in the aaa authentication login Console local command.

Add the aaa authentication login default group tacacs+ local-case command to the globalconfiguration.

Add the login authentication Console command to the line configuration

Question # 71

Refer to the exhibit.

A router receiving BGP routing updates from multiple neighbors for routers in AS 690. What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than 10.222.1.1?

The local preference value in another neighbor statement is higher than 250.

The local preference value should be set to the same value as the weight in the route map.

The route map is applied in the wrong direction.

The weight value in another neighbor statement is higher than 200.

Question # 72

Refer to the exhibit.

An IP SLA is configured to use the backup default route when the primary is down, but it is not working as desired. Which command fixes the issue?

R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2 10 track 1

R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2

R1(config)#ip sla track 1

R1(config)# ip route 0.0.0.0.0.0.0.0.1.1.1.1 track 1

Question # 73

Refer to Exhibit.

Which statement about redistribution from BGP into OSPF process 10 is true?

Network 172.16.1.0/24 is not redistributed into OSPF.

Network 10.10 10.0/24 is not redistributed into OSPF

Network 172.16.1.0/24 is redistributed with administrative distance of 1.

Network 10.10.10.0/24 is redistributed with administrative distance of 20.

Question # 74

Refer to the exhibit.

An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through

router R2. Which debug command is used to troubleshoot this issue?

debug ip flow

debug ip sla error

debug ip routing

debug ip packet