Exact2Pass
Last Update 11 hours ago Total Questions : 642
The Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI) content is now fully updated, with all current exam questions added 11 hours ago. Deciding to include 300-410 practice exam questions in your study plan goes far beyond basic test preparation.
You'll find that our 300-410 exam questions frequently feature detailed scenarios and practical problem-solving exercises that directly mirror industry challenges. Engaging with these 300-410 sample sets allows you to effectively manage your time and pace yourself, giving you the ability to finish any Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI) practice test comfortably within the allotted time.
Refer to the exhibit. A prefix of 10.1.1.0/31 is assigned for the DWDM circuit between R1 and R2 to connect the two attached VRFs on each router. Which configuration provides the required connectivity on R1?
Refer to the exhibit The engineer configured route redistribution in the network but soon received reports that R2 cannot access 192 168 7 0/24 and 192 168 15 0/24 subnets Which configuration resolves the issue?
IPv6 is enabled in the infrastructure to support customers with an IPv6 network over WAN and to connect the head office to branch offices in the local network. One of the customers is already running IPv6 and wants to enable IPv6 over the DMVPN network infrastructure between the headend and branch sites. Which configuration command must be applied to establish an mGRE IPv6 tunnel neighborship?
Refer to the exhibit. Router R1 peers with two ISPs using static routes to get to the internet. The requirement is that R1 must prefer ISP-A under normal circumstances and failover to ISP-B if the connectivity to ISP-A is lost. The engineer observes that R1 is load balancing traffic across the two ISPs Which action resolves the issue by sending traffic to ISP-A only with failover to ISP-B?
Refer to the exhibit.
A network engineer must establish communication between three different customer sites with these requirements:
Site-A: must be restricted to access to any users at Site-B or Site-C.
Site-B and Site-C must be able to communicate between sites and share routes using OSPF.
Which configuration meets the requirements?
Refer to the exhibit.
An OSPF neighbor relationship between R2 and R3 is showing stuck in EXCHANGE/EXSTART state. The neighbor is established between R1 and R2. The network engineer can ping from R2 to R3 and vice versa, but the
neighbor is still down. Which action resolves the issue?
Refer to the exhibit. An engineer must troubleshoot a connectivity issue impacting the redistribution of the subnet 172.16.2.48/28 into the OSPF domain. Which configuration on router R1 advertises this subnet into the OSPF domain?
Refer to the exhibit.
An engineer configures SW101 to send OSPFv3 interfaces state change messages to the server. However, only some OSPFv3 errors are being recorded. which organization resolves the ..?
Refer to the exhibit.
The R1 OSPF neighbor is not receiving type 5 external LSAs for 132.108.2.0/24 and 132.108.3.0/24 networks. Which configuration command resolves the issue?
Which protocol must be secured with MD-5 authentication across the MPLS cloud to prevent hackers from introducing bogus routers?
An administrator attempts to download the pack NBAR2 file using TFTP from the CPE router to another device over the Gi0/0 interface. The CPE is configured as below:
The transfer fails. Which action resolves the issue?
Exhibit.
Refer to the exhibit. A network is configured for EIGRP equal-cost load balancing, but the traffic destined to the servers is not load balanced. Link metrics from router R2 to R3 and R4 are the same. Which delay value must be configured to resolve the issue?
Exhibit.
Refer to the exhibit. The router is redistil bating a prefix 172.16.10.0tt4 that should have been filtered. Which action resolves the issue?
Drag and drop the IPv6 first hop security device roles from the left onto the corresponding descriptions on the right.
Which group of components works together to create an MPLS VPN?
Graphical user interface, text, application, email Description automatically generated