Answer A,E is correct: A. configure the helto and dead timers to match on both sides; E. configure both interfaces with the same area ID. OSPF decisions depend on router IDs, area membership, matching timers, network type, interface state, and cost calculation rather than arbitrary route preference. Cisco CCNA 200-301 v1.1 includes this topic under IP Connectivity, so the answer must be validated against normal Cisco device behavior and the operational wording of the scenario. The key is not simply recognizing a familiar acronym; it is identifying what the feature does, where it is configured, and what result it produces. Distractors that mention process IDs, unrelated metrics, or the wrong interface parameter do not satisfy OSPF neighbor or route-selection requirements. In a real network, selecting the wrong option would either leave the feature nonfunctional, create a forwarding or security gap, or send troubleshooting in the wrong direction. The selected answer is the only one that matches the stated requirement and the way Cisco switching, routing, services, security, wireless, or automation functions are expected to operate. This is why the verified answer remains the best technical choice for the question.

The user enters a user name and password, and then clicks a notification in an authentication app on a mobile device. Security fundamentals questions test the boundary between identity, authorization, accounting, encryption, inspection, and access-control functions. Cisco CCNA 200-301 v1.1 includes this topic under Network Fundamentals, so the answer must be validated against normal Cisco device behavior and the operational wording of the scenario. The key is not simply recognizing a familiar acronym; it is identifying what the feature does, where it is configured, and what result it produces. The other answers confuse identity checking with traffic filtering, or they assign the correct security idea to the wrong device or protocol. In a real network, selecting the wrong option would either leave the feature nonfunctional, create a forwarding or security gap, or send troubleshooting in the wrong direction. The selected answer is the only one that matches the stated requirement and the way Cisco switching, routing, services, security, wireless, or automation functions are expected to operate. This is why the verified answer remains the best technical choice for the question.

Add VLAN 13 to the trunk links on Switch A and Switch B for VLAN propagation. Switching features such as trunks and EtherChannels are controlled by negotiation mode, encapsulation, VLAN membership, and whether the selected protocol is Cisco proprietary or standards based. Cisco CCNA 200-301 v1.1 includes this topic under Network Access, so the answer must be validated against normal Cisco device behavior and the operational wording of the scenario. The key is not simply recognizing a familiar acronym; it is identifying what the feature does, where it is configured, and what result it produces. The incorrect options either disable negotiation, select the wrong negotiation protocol, or configure a mode that cannot form the requested link under the stated conditions. In a real network, selecting the wrong option would either leave the feature nonfunctional, create a forwarding or security gap, or send troubleshooting in the wrong direction. The selected answer is the only one that matches the stated requirement and the way Cisco switching, routing, services, security, wireless, or automation functions are expected to operate. This is why the verified answer remains the best technical choice for the question.

Cisco CCNA 200-301 v1.1 Network Fundamentals questions of this type test whether each item is matched to the technology that actually performs that role. The reliable method is to classify each term by operating layer, packet behavior, management function, or security purpose before matching it. Several terms in these items are legitimate Cisco networking concepts, but they become wrong when assigned to the wrong protocol or plane. The mapping retained in the document follows that separation: transport behavior is matched to TCP or UDP, wireless or security terms are matched to their mechanisms, and automation items are matched to the correct API or management model. This matters operationally because troubleshooting fails quickly when a forwarding-plane function is treated as a management-plane feature or when a security control is applied to the wrong threat. The shown mapping is therefore retained as the verified response.

To subnet 172.25.0.0/16 to meet the subnet requirements and maximize the number of hosts, you need to determine how many bits you need to borrow from the host portion of the address to create enough subnets for 32 sites. Since 32 is 2^5, you need to borrow 5 bits, which means your new subnet mask will be /21 or 255.255.248.0. To find the second subnet, you need to add the value of the fifth bit (32) to the third octet of the network address (0), which gives you 172.25.32.0/21 as the second subnet. The first usable IP address in this subnet is 172.25.32.1, and the last usable IP address is 172.25.39.254.

To assign the first usable IP address to e0/0 on Sw101, you need to enter the following commands on the device console:

Sw101#configure terminal Sw101(config)#interface e0/0 Sw101(config-if)#ip address 172.25.32.1 255.255.248.0 Sw101(config-if)#no shutdown Sw101(config-if)#end

To assign the last usable IP address to e0/0 on Sw102, you need to enter the following commands on the device console:

Sw102#configure terminal Sw102(config)#interface e0/0 Sw102(config-if)#ip address 172.25.39.254 255.255.248.0 Sw102(config-if)#no shutdown Sw102(config-if)#end

To subnet an IPv6 GUA to meet the subnet requirements and maximize the number of hosts, you need to determine how many bits you need to borrow from the interface identifier portion of the address to create enough subnets for 32 sites. Since 32 is 2^5, you need to borrow 5 bits, which means your new prefix length will be /69 or ffff:ffff:ffff:fff8::/69 (assuming that your IPv6 GUA has a /64 prefix by default). To find the second subnet, you need to add the value of the fifth bit (32) to the fourth hextet of the network address (0000), which gives you xxxx:xxxx:xxxx:0020::/69 as the second subnet (where xxxx:xxxx:xxxx is your IPv6 GUA prefix). The first and last IPv6 addresses in this subnet are xxxx:xxxx:xxxx:0020::1 and xxxx:xxxx:xxxx:0027:ffff:ffff:ffff:fffe respectively.

To assign an IPv6 GUA using a unique 64-bit interface identifier on e0/0 on Sw101, you need to enter the following commands on the device console (assuming that your IPv6 GUA prefix is 2001:db8::/64):

Sw101#configure terminal Sw101(config)#interface e0/0 Sw101(config-if)#ipv6 address 2001:db8::20::1/69 Sw101(config-if)#no shutdown Sw101(config-if)#end

To assign an IPv6 GUA using a unique 64-bit interface identifier on e0/0 on Sw102, you need to enter the following commands on the device console (assuming that your IPv6 GUA prefix is 2001:db8::/64):

Sw102#configure terminal Sw102(config)#interface e0/0 Sw102(config-if)#ipv6 address 2001:db8::27::fffe/69 Sw102(config-if)#no shutdown Sw102(config-if)#end

4. Automation questions depend on recognizing controllers, APIs, data formats, HTTP methods, and cloud-service characteristics. Cisco CCNA 200-301 v1.1 includes this under Automation and Programmability, where the expected skill is identifying the mechanism that actually satisfies the scenario. The wording usually gives the decisive clue: a protocol number, a route prefix, a control-plane role, a wireless security method, or a management command. The wrong options mix controller functions with data-plane forwarding or confuse API operations with unrelated management terms. In a real network, selecting the wrong option would usually produce a failed adjacency, broken client connectivity, insecure management access, or an incorrect forwarding path. The selected answer matches the Cisco behavior and configuration model required by the question, so it is retained as the verified answer for this item.

when a gateway protocol is required that support more than two Cisco devices for redundancy. IP services must be selected by their exact operational role: addressing, translation, time, monitoring, logging, redundancy, or traffic treatment. Cisco CCNA 200-301 v1.1 includes this under IP Connectivity, where the expected skill is identifying the mechanism that actually satisfies the scenario. The wording usually gives the decisive clue: a protocol number, a route prefix, a control-plane role, a wireless security method, or a management command. The wrong options name real services or commands, but they solve a different infrastructure problem. In a real network, selecting the wrong option would usually produce a failed adjacency, broken client connectivity, insecure management access, or an incorrect forwarding path. The selected answer matches the Cisco behavior and configuration model required by the question, so it is retained as the verified answer for this item.

Cisco CCNA 200-301 v1.1 Network Fundamentals questions of this type test whether each protocol, component, address type, or management concept is matched to its correct operating role. The safe method is to classify every item by function: what it does, where it operates, and what problem it solves. Several distractors are usually valid networking terms, but they belong to a different layer or a different operational workflow. The shown mapping keeps those boundaries straight and avoids assigning a feature to the wrong technology. In practice, this same skill is required when troubleshooting because confusing a management-plane function with a forwarding-plane function, or a wireless security feature with an authentication feature, leads to incorrect fixes. The mapping shown in the file is therefore retained and explained as the verified selection.

Select WPA2 Policy Disable PMF Enable PSK. Wireless questions depend on AP mode, WLAN security, RF band selection, controller interfaces, and client roaming or authentication behavior. Cisco CCNA 200-301 v1.1 includes this under Network Access, where the expected skill is selecting the feature that actually produces the requested network behavior. The wording normally gives the clue: protocol family, address scope, trunk state, route preference, security mode, API method, or controller role. Wrong options confuse encryption with authentication, local switching with tunneling, or controller management with client data handling. In production, choosing the wrong option would typically cause failed client access, a broken route, insecure management, or an automation workflow that targets the wrong interface. The selected answer is the Cisco-consistent behavior for this item.

Answer B,C is correct: B. Option B; C. Option C. The answer follows directly from normal Cisco device behavior and the wording of the scenario. Cisco CCNA 200-301 v1.1 includes this under IP Connectivity, where the exam expects engineers to recognize the device behavior that actually produces the required outcome. The question is best solved by reading the operational clue rather than choosing a familiar acronym. The other choices are either adjacent technologies, wrong-layer functions, or settings that would not produce the stated result. In a production network, the wrong choice would normally create an outage, leave a management or security gap, or send troubleshooting toward the wrong subsystem. The selected answer is the one that matches the control-plane, data-plane, wireless, security, services, or automation mechanism described in the question. That is why it remains the verified answer for this item.

R1(config)#ipv6 route 2019:C15C:0CAF:E001::/64 2019:C15C:0CAF:E002::1. IPv6 static routes are configured in global configuration mode with the ipv6 route command. The destination prefix comes first, followed by the next-hop IPv6 address or exit interface information. The options using ip route are IPv4 syntax and cannot install an IPv6 route. The options shown in interface configuration mode are also invalid for adding a global static route. Cisco CCNA 200-301 v1.1 IP Connectivity expects engineers to separate IPv4 and IPv6 routing syntax and to recognize that an IPv6 route to a /64 prefix is not configured with the IPv4 ip route command. The corrected answer uses ipv6 route 2019:C15C:0CAF:E001::/64 with the next-hop address 2019:C15C:0CAF:E002::1. That directs traffic for the destination IPv6 network toward the specified next hop.

access-list 101 permit tcp 10.1.10 0.0.0.255 172.16.10 0.0.0.255 eq ssh. Cisco routers select forwarding paths by longest-prefix match first, then administrative distance and metric when comparable routes compete. Cisco CCNA 200-301 v1.1 includes this under Security Fundamentals, where the exam expects engineers to recognize the device behavior that actually produces the required outcome. The question is best solved by reading the operational clue rather than choosing a familiar acronym. The wrong choices either do not match the destination, use the wrong next hop, or fail to provide the intended primary/backup behavior. In a production network, the wrong choice would normally create an outage, leave a management or security gap, or send troubleshooting toward the wrong subsystem. The selected answer is the one that matches the control-plane, data-plane, wireless, security, services, or automation mechanism described in the question. That is why it remains the verified answer for this item.

unique local address. The clue is that the IPv6-only device must be reachable from the internal network, not only from the directly connected link and not from the public Internet. A unique local address uses the FC00::/7 space and is intended for local communications inside an organization. A link-local address would fail the requirement because FE80::/10 works only on the local segment and is not routed between internal subnets. A global unicast address is publicly routable and would not satisfy the internal-only requirement. Cisco CCNA 200-301 v1.1 Network Fundamentals expects this exact distinction between IPv6 scopes: link-local for one link, unique local for private internal routing, and global unicast for Internet-routable reachability. The corrected answer is unique local address. That address type gives the engineer a routable internal IPv6 address while keeping the address outside global Internet advertisement expectations.

Cisco CCNA 200-301 v1.1 Network Fundamentals questions of this type test whether each item is matched to the technology that actually performs that role. The reliable method is to classify each term by operating layer, packet behavior, management function, or security purpose before matching it. Several terms in these items are legitimate Cisco networking concepts, but they become wrong when assigned to the wrong protocol or plane. The mapping retained in the document follows that separation: transport behavior is matched to TCP or UDP, wireless or security terms are matched to their mechanisms, and automation items are matched to the correct API or management model. This matters operationally because troubleshooting fails quickly when a forwarding-plane function is treated as a management-plane feature or when a security control is applied to the wrong threat. The shown mapping is therefore retained as the verified response.

Authentication verifies the identity of a person accessing a network, and authorization determines what resource a user can access.. IP services must be selected by their exact operational role: addressing, translation, time, monitoring, logging, redundancy, or traffic treatment. Cisco CCNA 200-301 v1.1 includes this under Security Fundamentals, where the expected skill is identifying the mechanism that actually satisfies the scenario. The wording usually gives the decisive clue: a protocol number, a route prefix, a control-plane role, a wireless security method, or a management command. The wrong options name real services or commands, but they solve a different infrastructure problem. In a real network, selecting the wrong option would usually produce a failed adjacency, broken client connectivity, insecure management access, or an incorrect forwarding path. The selected answer matches the Cisco behavior and configuration model required by the question, so it is retained as the verified answer for this item.

Add either the ip nat {inside|outside} command under both interfaces.. IP services must be selected by their exact operational role: addressing, translation, time, monitoring, logging, redundancy, or traffic treatment. Cisco CCNA 200-301 v1.1 includes this under IP Services, where the expected skill is identifying the mechanism that actually satisfies the scenario. The wording usually gives the decisive clue: a protocol number, a route prefix, a control-plane role, a wireless security method, or a management command. The wrong options name real services or commands, but they solve a different infrastructure problem. In a real network, selecting the wrong option would usually produce a failed adjacency, broken client connectivity, insecure management access, or an incorrect forwarding path. The selected answer matches the Cisco behavior and configuration model required by the question, so it is retained as the verified answer for this item.

static. The answer follows directly from normal Cisco device behavior and the wording of the scenario. Cisco CCNA 200-301 v1.1 includes this under Network Access, where the exam expects engineers to recognize the device behavior that actually produces the required outcome. The question is best solved by reading the operational clue rather than choosing a familiar acronym. The other choices are either adjacent technologies, wrong-layer functions, or settings that would not produce the stated result. In a production network, the wrong choice would normally create an outage, leave a management or security gap, or send troubleshooting toward the wrong subsystem. The selected answer is the one that matches the control-plane, data-plane, wireless, security, services, or automation mechanism described in the question. That is why it remains the verified answer for this item.

Router2(config)#ntp master 4. If Router1 is configured as an NTP client using the ntp server command, Router2 must provide time as an NTP server. On Cisco IOS, the command ntp master with an optional stratum value configures a router to act as an authoritative NTP source for other devices. The command ntp server points a device toward another time source; it does not make that device the server for Router1. Cisco CCNA 200-301 v1.1 IP Services requires candidates to separate NTP client configuration from NTP server behavior. In this scenario, Router1 already references 192.168.0.3 as its time source. Router2 must therefore be configured as the local master clock, and stratum 4 is a valid configured stratum. The correct configuration is ntp master 4.

Option B. IPv6 questions depend on address scope, prefix representation, and whether the address is unicast, multicast, anycast, link-local, or global. Cisco CCNA 200-301 v1.1 includes this under IP Connectivity, where the exam expects engineers to recognize the device behavior that actually produces the required outcome. The question is best solved by reading the operational clue rather than choosing a familiar acronym. The wrong choices represent a different IPv6 address behavior or an invalid compressed form. In a production network, the wrong choice would normally create an outage, leave a management or security gap, or send troubleshooting toward the wrong subsystem. The selected answer is the one that matches the control-plane, data-plane, wireless, security, services, or automation mechanism described in the question. That is why it remains the verified answer for this item.

Cisco CCNA 200-301 v1.1 Network Fundamentals questions of this type test whether each item is matched to the technology that actually performs that role. The reliable method is to classify each term by operating layer, packet behavior, management function, or security purpose before matching it. Several terms in these items are legitimate Cisco networking concepts, but they become wrong when assigned to the wrong protocol or plane. The mapping retained in the document follows that separation: transport behavior is matched to TCP or UDP, wireless or security terms are matched to their mechanisms, and automation items are matched to the correct API or management model. This matters operationally because troubleshooting fails quickly when a forwarding-plane function is treated as a management-plane feature or when a security control is applied to the wrong threat. The shown mapping is therefore retained as the verified response.