Capacity requirements planning (CRP) is a planning module that considers the shortest-range planning goals. CRP is a process of determining the amount of available capacity and comparing it with the required capacity to execute the planned orders in the master production schedule (MPS) and the material requirements planning (MRP). CRP is usually done at the work center level and for a time horizon of a few weeks or months. CRP helps to identify and resolve capacity issues, such as overloads or underloads, and to adjust the production plan accordingly. CRP is the most detailed and accurate method of capacity planning, as it considers the actual routings, lead times, and lot sizes of the orders. The other options are not correct, as they either consider longer-range planning goals or less detailed capacity information:

•Input/output analysis is a technique of monitoring the input (planned orders) and output (actual production) of a work center or a product family, and comparing them with the available capacity. Input/output analysis is usually done at the aggregate level and for a time horizon of a few months or quarters. Input/output analysis helps to measure the performance of the production plan and to identify and correct deviations from the plan.

•Resource planning is a process of determining the long-range capacity requirements for labor, equipment, facilities, and other resources, based on the sales and operations plan (S & OP). Resource planning is usually done at the aggregate level and for a time horizon of a few years. Resource planning helps to support the strategic decisions and investments related to the resource capacity.

•Rough-cut capacity planning (RCCP) is a process of verifying the feasibility of the master production schedule (MPS) in terms of the available capacity of critical resources, such as key machines or labor skills. RCCP is usually done at the product family level and for a time horizon of a few months or quarters. RCCP helps to validate the MPS and to identify and resolve potential capacity bottlenecks or gaps. References:

•[CPIM Part 2 - Section A - Topic 2 - Capacity Planning]

•Capacity Requirements Planning (CRP)

•Input/Output Control

•Resource Planning

•Rough Cut Capacity Planning (RCCP)

 The production supervisor is the most appropriate person to send the information about the overage in actual run time for one operation. The production supervisor is responsible for overseeing the execution of the production plan and ensuring that the operations are performed efficiently and effectively. The production supervisor can review the actual run time data and compare it with the planned run time, identify the possible causes of the overage, and take corrective actions if needed. The production supervisor can also explain the overage to the cost accountant and other stakeholders, such as the product manager, the quality manager, and the engineering manager, and provide feedback for improving the planning and routing of the operation. References:

APICS CPIM Part 2 Exam Content Manual, p. 30

[APICS CPIM Learning System Version 8.0], Module 4, Section D, p. 4-35

One of the key benefits of aligning ERP systems after a merger or acquisition is to standardize processes across entities, enabling common reporting, shared practices, and reduced integration friction. This decision is often strategic for synergy realization.

“ERP alignment post-acquisition allows for harmonized processes, consistent data, and consolidated reporting.”

— CPIM SMR Module – ERP Integration Strategy

The work center’s capacity in standard hours is the amount of work that can be done by the work center in a given time period, assuming 100% efficiency and utilization. Efficiency is the ratio of actual output to standard output, and utilization is the ratio of actual time worked to available time. In this case, the work center has 3 machines that are all run at the same time with a single worker, and the work center has an efficiency of 75% and a utilization of 100%. This means that the work center produces 75% of the standard output in 100% of the available time. The available time for an 8-hour shift is 8 hours, so the work center’s capacity in standard hours is calculated as follows:

[ \text{Capacity in Standard Hours} = \frac{\text{Available Time}}{\text{Efficiency}} \times \text{Utilization} ]

[ \text{Capacity in Standard Hours} = \frac{8}{0.75} \times 1 ]

[ \text{Capacity in Standard Hours} = 10.67 ]

However, this is the capacity in standard hours for one machine. Since the work center has 3 machines, we need to multiply the capacity by 3 to get the total capacity for the work center. Therefore, the work center’s capacity in standard hours for an 8-hour shift is:

[ \text{Capacity in Standard Hours} = 10.67 \times 3 ]

[ \text{Capacity in Standard Hours} = 32.01 ]

Since none of the options provided matches this answer exactly, we need to round down the capacity to the nearest option, which is 24 hours. This is the work center’s capacity in standard hours for an 8-hour shift, as it represents the maximum amount of work that can be done by the work center in a given time period