The best answer is B. Fan speed and airflow through the heat sinks. The symptoms strongly indicate overheating: the computer works normally at first, slows down as heat builds up, then locks up and powers off to protect the CPU/GPU and motherboard. The Quentin Docter study guide states that a PC that works for a few minutes and then locks up is probably overheating because a heat sink or fan is not functioning properly, and the first troubleshooting step is to check all internal fans and ensure the heat sinks are properly attached. High-end gaming systems are especially heat-sensitive because CPUs and dedicated graphics cards generate substantial heat under load. The same section notes that CPUs are common overheating sources and video cards are also very susceptible in gaming or graphics-heavy systems. Power supply testing is useful for intermittent power problems, but the gradual slowdown before shutdown points more directly to thermal throttling and heat buildup than voltage failure.

=========

The correct answer is B. Inspect and replace the printer rollers.

According to CompTIA A+ Core 1 220-1201 objectives under Printers:

Frequent paper jams with no visible obstruction are often caused by worn or dirty feed rollers, which fail to grip and feed paper properly.

Inspecting and replacing the rollers ensures smooth paper feeding and prevents repeated jams, particularly in high-use network printers.

Why the other options are incorrect:

A. Check for firmware updates: Firmware updates address software or functionality issues, not mechanical paper feeding problems.

C. Reseat the fuser assembly: Fuser issues typically cause smudging or incomplete toner adhesion, not paper jams.

D. Clean the corona wire: The corona wire affects toner adhesion and print quality, not paper feeding.

C. Initiate the system restore:

If the technician is confident that rolling back the system to a previous restore point will resolve the issue, the next logical step is to initiate the System Restore process.

System Restore allows the system to revert to a state before the OS update, which can eliminate the performance issues caused by the update.

Incorrect Options:

A. Document the findings: Documentation is important but should occur after resolving the issue.

B. Investigate any recent infrastructure changes: This is unnecessary if the issue is already attributed to the OS update.

D. Verify full system functionality: This step should be performed after the System Restore is completed.

Key Takeaway: When confident that rolling back will resolve the issue, the technician should proceed with initiating a System Restore to revert the OS.

When troubleshooting intermittent latency to a remote internal resource, CompTIA A+ recommends using tools that help identify where latency occurs and whether it is consistent or fluctuating over time. The best tools for this scenario are ping -t and tracert.

Ping -t (B) sends continuous ICMP echo requests, allowing the technician to observe packet loss, fluctuating response times, or timeouts. This helps identify intermittent connectivity problems that occur at specific times, such as bandwidth congestion, routing instability, or wireless interference.

Tracert (F) maps each hop between the local workstation and the remote office. If latency spikes occur only after a particular hop—such as a VPN tunnel, MPLS gateway, or inter-office router—that device becomes the suspected bottleneck. This makes tracert essential for isolating WAN-related slowdowns.

Ipconfig /all (A) only provides local configuration and does not diagnose latency. Nslookup (C) is for DNS testing—not latency to a specific internal host. Examining switchports (D) helps with local issues but not remote latency. QoS (E) is a solution, not a troubleshooting step. Calling ISP (G) may be premature unless testing confirms ISP-related issues.

Thus, ping -t and tracert are the correct diagnostic tools.

If a print spooler crashes specifically with one application and no issue occurs on other systems, the most likely root cause is a bug within that specific application. Restarting the spooler and reinstalling drivers resolves system-wide or hardware-related issues not app-specific failures. This indicates the application may be sending malformed print data.

An internal cloud platform operated exclusively for a single organization is a private cloud, providing dedicated resources and enhanced control.

From CompTIA A+ 220-1101 Official Study Guide, Objective 3.7 – Cloud models:

“A private cloud is provisioned for exclusive use by a single organization, typically managed internally or by a third party, and may be hosted on-premises.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 3: Cloud Concepts

CompTIA Exam Objectives 220-1101, Domain 3.7

============

A shutdown during POST combined with a burning smell strongly indicates an overheating condition occurring almost immediately after power-on. In a newly built workstation, the most common cause of rapid CPU overheating is improper heatsink installation, especially failing to apply thermal paste (thermal compound) between the CPU and the heatsink. Thermal paste fills microscopic imperfections between the two metal surfaces so heat can transfer efficiently into the heatsink. Without it, the CPU can spike to unsafe temperatures within seconds. Modern systems detect this and trigger protective thermal shutdown during POST to prevent permanent CPU or motherboard damage. The burning smell can occur when components near the CPU socket heat excessively or when protective coatings/dust residues warm quickly due to poor heat dissipation.

The wrong type of RAM (B) would more likely cause no-boot/beep codes rather than a burning smell. Not properly grounding (A) relates to ESD damage risk, but that typically causes intermittent or dead hardware symptoms, not immediate thermal shutdown. A disconnected case exhaust fan (C) can contribute to higher case temperatures, but it’s less likely to cause an immediate POST shutdown compared to missing thermal paste on the CPU cooler.

The correct answer is A. Adjust the SMTP server configurations for email.

Scan-to-email functionality on a multifunction printer relies on proper configuration of an SMTP (Simple Mail Transfer Protocol) server. The printer must know how to send outgoing email, which requires settings such as:

SMTP server address

Port number (commonly 25, 465, or 587)

Authentication credentials (username/password)

Encryption method (SSL/TLS if required)

If scan-to-email is not working, the most common cause is incorrect or missing SMTP configuration. Without this setup, the printer cannot send scanned documents via email.

Why the other options are incorrect:

B. Check the printer ' s IP address configuration

This ensures network connectivity, but since the printer is already in use and the issue is specific to email functionality, IP configuration is unlikely the root cause.

C. Install the printer ' s driver software on all computers

Drivers are needed for printing from computers, but scan-to-email is handled directly by the printer and does not depend on client-side drivers.

D. Configure user authentication settings for email access

While authentication may be required in some setups, it is part of the broader SMTP configuration. The primary and most direct fix is ensuring SMTP settings are correct.

Exam Tip (Core 1 220-1201):

Scan-to-email issues → Check SMTP settings first

Multifunction printers rely on network services (email protocols), not just drivers

Final Answer: A. Adjust the SMTP server configurations for email

The technician will configure the MX record on a DNS server. An MX, or Mail Exchange, record is a DNS resource record that identifies the mail server responsible for accepting email for a particular domain. It can also include a priority value so that sending systems know which mail server to contact first when multiple servers are available. Although the record points to a mail server, it is created and maintained within the domain’s DNS zone rather than directly on the mail server. A proxy server intermediates network requests and is unrelated to DNS email-routing records. A print server manages printers and print queues and has no role in email delivery. Therefore, the DNS management interface or authoritative DNS server for the domain is where the technician must create or modify the MX record.

Plenum cabling is designed for use in commercial spaces where cables run through air ducts or plenum spaces, as it has fire-resistant properties and emits less toxic smoke.

Why Not A (USB 3.1 Gen 2): USB is for peripheral connections, not large-scale commercial installations.

Why Not B (Straight tip fiber connector): Fiber connectors are for high-speed connections but are not specifically for commercial spaces.

Why Not D (Cat 8): While Cat 8 is high-speed, it is not uniquely suited for commercial spaces like plenum cabling.

CompTIA A+ Exam Reference: Core 1 (220-1201), Section 3.1, cabling standards​.

Pixel density explains why the image appears smaller at 4K resolution when the physical monitor size and magnification level remain unchanged. A 4K display contains substantially more pixels within the same physical screen area than an HD display. As a result, each individual pixel is physically smaller, and an image displayed at its native pixel dimensions occupies less physical space on the higher-resolution screen. Pixel density is commonly measured in pixels per inch. Refresh rate determines how many times the screen updates each second and affects motion smoothness rather than image size. Backlight zones control brightness and contrast in displays that use local dimming. Panel type, such as IPS, VA, or OLED, influences colour reproduction, response time, viewing angles, and contrast. None of these characteristics explains the difference in physical image size. The higher pixel density of the 4K display is therefore the correct reason.

When a newly built computer successfully passes POST, it indicates that the CPU, RAM, motherboard, video output, and other essential components are functioning at a hardware level. POST will typically fail or display error codes if there are problems with the CPU, RAM, GPU, or power delivery. Therefore, the fact that POST succeeds allows us to eliminate those components from suspicion.

The issue arises after POST, when the system attempts to load an operating system. For the OS to load, the BIOS/UEFI must detect a working storage device—such as an HDD, SSD, or NVMe drive—containing a bootable OS. If the computer cannot locate or read the drive, the system will halt at a boot error, such as “No boot device found,” “Insert boot media,” or similar messages. This is consistent with a failed or improperly connected HDD.

A failed HDD prevents access to boot files, even though the rest of the system hardware functions normally. Audio cards are irrelevant to booting. A failed CPU would cause a POST failure, not an OS loading issue. A faulty power supply would affect system stability during POST, not specifically OS boot failure unless the system is not powering at all.

Thus, the failed component is the HDD.

A physical bulge under the trackpad is a classic CompTIA-identified symptom of a swollen lithium-ion battery. As batteries degrade, internal gas buildup expands the casing, pushing upward on the laptop chassis—often distorting the trackpad, keyboard, or bottom shell. This can cause cursor issues, clicking problems, and safety hazards.

Replacing the battery first is essential because swollen batteries can rupture, leak, or ignite. Only after the battery is removed and replaced should the technician evaluate whether the trackpad suffered permanent damage.

Replacing the trackpad (D) without addressing the battery fails to correct the root cause. The motherboard (A) and heat sink (B) are unrelated to the physical bulge.

Thus, the correct first step is replacing the battery.

A crimper is specifically used to attach RJ45 connectors to the ends of network cables. It pressesthe connector pins into the cable ' s wires, establishing a secure electrical connection. A punchdown tool is used for wiring patch panels or keystone jacks, not for attaching connectors.